Quick Answer: When Used For Emergencies Flags Should Be Orange?

What factors affect the flaggers location?

In rural areas, flagger stations should generally be located (see Figure 3): A minimum of 350 feet (105 m) in advance of the work area.

Factors such as visibility, traffic speeds and volume, road conditions, and the work being done should be considered in determining your proper location..

What is a Type 2 barricade?

Type II Barricades Lightweight and easy to handle, these traffic control devices are built to last and engineered to meet your specific needs and requirements. … Type II barricades come in two sizes, either 24″ or 36″ wide with extruded or fluted plastic panels from 8″ to 12″.

What is a road taper?

The taper is the transition area in a work zone. Tapers are the only locations in work zones where a driver must adjust their travel path, making proper placement critical to the safety of the job site. Tapers are also used to transition traffic back to its normal path of travel at the end of the construction area.

What is a flagging operation?

Flaggers are provided at work sites to stop traffic intermittently as necessitated by work in progress or to maintain continuous traffic past a work site at reduced speeds to help protect the work crew. The following table includes some of the basic flagging operations to be followed on the job site.

Does the Mutcd require that you wear a hardhat?

2 High-Visibility Safety Apparel (MUTCD 6E. 02) Standard. For daytime activities, flaggers shall wear a high visibility hard hat, safety glasses, a Performance Class 3 top OR a Performance Class 2 top, and safety footwear.

Do flaggers have to wear hard hats?

Hard hats – Flaggers must wear a hard hat at all times. Other workers are required to wear a hard hat when performing certain work activities or when required by the supervisor to do so.

What factors affect your location?

Several factors that influence location positioning include the location of raw materials, proximity to the market, climate, and culture.

What is disobey traffic device?

Disobeying a traffic control device is a two-point ticket in the State of New York and carries a fine of up to $150 plus a surcharge. Very often disobeying a traffic control device ticket is given in lieu of what we call a roadside reduction, such as speeding, based upon another traffic infraction.

Can construction workers stop traffic?

They have no powers to stop traffic or require drivers to obey their instructions. Strictly speaking they’re commiting an offence, though if it done quickly cleanly, and in the name of safety i doubt they’d ever get fingered.

Where should a flagger stand?

The flagger should stand either on the shoulder adjacent to the road user being controlled or in the closed lane prior to stopping road users. A flagger should only stand in the lane being used by moving road users after road users have stopped.

What does a flagger sign mean?

ROAD CONSTRUCTION AHEADFLAGGER AHEAD. The sign is also known as ROAD CONSTRUCTION AHEAD. This traffic signs warns you that a flagger is controlling traffic ahead. Flaggers use STOP and SLOW paddles or a red flag to signal traffic to stop or slow down. Pay special attentions to flaggers when approaching and traveling through a work zone.

When used for emergencies flags must be red or red orange?

09 Flags, when used, shall be red or fluorescent orange/red in color, shall be a minimum of 24 inches square, and shall be securely fastened to a staff that is approximately 36 inches in length.

What is the first thing you should do if a driver disobeys your command and keeps going?

What is the FIRST thing you should do if a driver disobeys your command and keeps going? 24. You should allow the right-of-way to EMERGENCY VEHICLES as soon as safely possible. STOP HERE AND GIVE YOUR EXAMINATION QUESTIONS AND ANSWER SHEET TO YOUR COURSE INSTRUCTOR.

What are the 5 parts of a traffic control zone?

The work zone typically consists of 5 parts:Advanced Warning Area. This area is the most important since it: … Transition Area. Narrow pavement, reduction of travel lanes, or a lane closure may require moving traffic out of its normal path. … Buffer Area.

Do flaggers get breaks?

ADDITIONAL TRAFFIC CONTROL ISSUES If a driver ignores the flagger’s instructions, do not stop flagging. … Flaggers should have frequent breaks (no more than two hours of flagging, or as required by the States). The hotter, colder, windier, or wetter the conditions, the more frequently flaggers should have breaks.

How do you slow down traffic on a flag?

To Alert Or Slow Traffic The flagger shall face road users and slowly wave the flag in a sweeping motion of the extended arm from shoulder level to straight down without raising the arm above a horizontal position.

What are the 7 location factors for industry?

Factors responsible for location of Industries Some of them are: raw material, land, water, labor, capital, power, transport, and market.

What factors do you need to consider when choosing a plant location?

12 Factors to Consider When Choosing a Pharmaceutical Plant Location2.1 1. Availability of raw materials.2.2 2. Nearness to the market.2.3 3. Constant Power supply.2.4 4. Supply of Labour.2.5 5. Transportation Networks.2.6 6. Communication.2.7 7. Water supply.2.8 8. Suitability of land and climate.More items…•

What is the importance of location decision?

Location decisions are often important – to both large and small businesses. The location decision has a direct effect on an operation’s costs as well as its ability to serve customers (and therefore its revenues). Also, location decisions, once made, are difficult and costly to undo.

When used for emergencies flags should be?

Warning flags should only be used during emergency situations or when there are low-speed and low-volume locations that can easily be controlled by a single flagger. If the flag is going to be used for signaling, it should be at least 24 inches square and made from high-quality material and red.

What are the 5 main components of a traffic control zone?

Most temporary traffic control zones are divided into four areas: the advance warning area, the transition area, the activity area, and the termination area.

Do flaggers have authority?

Keep in mind that as a flagger you are not the “law.” That is, you do not have the LEGAL AUTHORITY that police officers have to regulate, control or direct traffic. Uniformed police officers are responsible for traffic control in signalized intersections, not flaggers.

How can employers control traffic?

Always use barriers, barricades, lane control devices, traffic signal lights, sign trucks, and other methods as appropriate instead of, and/or in addition to, traffic control persons to ensure the safety of all workers.

What are the 4 traffic control devices?

In a work zone, the most common traffic control devices used to guide drivers safely through work zones include barricades, vertical signs, concrete barriers, barrels and cones. Traffic control devices communicate their message in several ways, by color, shape, words, symbols and placement to provide information.